WiseDave Posted April 21, 2019 Posted April 21, 2019 so i painted this with pearl lime green pearl wicked color over white autobourne sealer. The finish is pretty rough should i sand and clear coat? or just clear coat? any suggestions for a clear are welcomed 4
Phirewriter Posted April 21, 2019 Posted April 21, 2019 (edited) Wet sanding on a pearl will damage the pearl effect. All waterborne paints generally require a clear coat and most hobby lacquers or enamels will work. Automotive waterborne paint is generally always cleared with a 2k clear. So the answer is to clear and then sand and polish any imperfections. Createx has very good tutorials and general information on their website concerning topcoats for Wicked and AutoAir. Edited April 21, 2019 by Phirewriter
Miatatom Posted April 22, 2019 Posted April 22, 2019 I don't think you're going to be successful. From what I've learned about Createx paints, you can't sand them Put clear over them and sand and polish away. Just not on the color coats. I hope someone will prove me wrong. I like the paints.
Kit Basher Posted April 22, 2019 Posted April 22, 2019 How rough is it? If it's just some orange peel, you can probably clear and sand. If it's "sandy", you can sand the color coat and respray another color coat. I have not tried Wicked, but Auto Air sands nicely with 1000 grit sandpaper used dry. Once you have it smooth, try respraying the color using very thin paint, applied in a few light coats. If you don't sand thru the color, it shouldn't take much paint to give a smooth, even surface. Then you can clear with whatever clear you like. I've had good results with Duplicolor Perfect Match clear, but I've also tried Krylon and Testors and both work fine. It takes some practice to get used to these paints, but once you do, I think you will like them.
WiseDave Posted April 23, 2019 Author Posted April 23, 2019 So far i sanded it smooth. Repainted adding more reducer. So far looks great.I can't believe how hard these paints are. But yes Kit Basher once i figure out the ratio I think it will be awesome. Thank You
Miatatom Posted April 23, 2019 Posted April 23, 2019 14 hours ago, Kit Basher said: I have not tried Wicked, but Auto Air sands nicely with 1000 grit sandpaper used dry. I'm thinking that's the issue. I've heard Wicked can't be wet sanded. Might have assumed that included all forms of sanding. I'll have to try it soon.
Kit Basher Posted April 23, 2019 Posted April 23, 2019 35 minutes ago, Miatatom said: I'm thinking that's the issue. I've heard Wicked can't be wet sanded. Might have assumed that included all forms of sanding. I'll have to try it soon. Dry sanding is what Createx recommends. It's worked well for me. One thing that's helped me a lot, I downloaded and printed the Createx "Hard Surface Application Guide" Good instructions that apply to all their paints.
my80malibu Posted April 23, 2019 Posted April 23, 2019 On 4/22/2019 at 4:29 AM, Kit Basher said: How rough is it? If it's just some orange peel, you can probably clear and sand. If it's "sandy", you can sand the color coat and respray another color coat. I have not tried Wicked, but Auto Air sands nicely with 1000 grit sandpaper used dry. Once you have it smooth, try respraying the color using very thin paint, applied in a few light coats. If you don't sand thru the color, it shouldn't take much paint to give a smooth, even surface. Then you can clear with whatever clear you like. I've had good results with Duplicolor Perfect Match clear, but I've also tried Krylon and Testors and both work fine. It takes some practice to get used to these paints, but once you do, I think you will like them. I would agree with this. the paint job in question doesn't look to bad in the picture.
WiseDave Posted April 24, 2019 Author Posted April 24, 2019 it was 100 grit sand paper looking. Getting better thanks all
OldNYJim Posted April 24, 2019 Posted April 24, 2019 On 22 April 2019 at 10:54 PM, Kit Basher said: Dry sanding is what Createx recommends. It's worked well for me. One thing that's helped me a lot, I downloaded and printed the Createx "Hard Surface Application Guide" Good instructions that apply to all their paints. Same here - dry sanding works great, but wet sanding results in a rubbery paint which will probably start peeling.
WiseDave Posted April 27, 2019 Author Posted April 27, 2019 dry sanded looks great except in a couple spots. Repainted and clear with duplicolor looks darn good for my work site won't let me upload the 1 pic i have i'll to try another thanks again
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now