Chuck Most Posted April 13, 2013 Share Posted April 13, 2013 Here we go... First order of business was to cut away the top. Since this will be a two-seat roadster, there was a good foot and a half of space between the rear edge of the door and front of the rear wheel opening that I wouldn't need- so an approximate 18 scale inches was whacked out of that area. I used part of the AMT '53 Stude's chopped top option on the chopped windshield, and used the rest of it as a deck filler- this will be trimmed and shape as needed once seats, etc.. are decided upon. Here's everything roughed in- note that this will be a curbside model, with no full engine detail- the hood was glued into place and sanding/putty will be used to take care of the large gaps along the fenders. Quote Link to comment Share on other sites More sharing options...
Casey Posted April 17, 2013 Author Share Posted April 17, 2013 That looks great, Chuck. Nicely shortened. Will there be a lift off hardtop for it? I soldered the two main engine support brackets, the seat support crossbars, and the temporary front and rear axle tubes in place on the frame tonight...: ...then set the wheels and tire in place to check the ride height and tire-to-body clearance and everything looks good. Well, except for the driver who ended up sitting higher than I wanted: I need to recline him a bit more so that only his goggles are above the body shell, and I may end up using a thinner seat, too, as the styrene seat is about as thin as it can get. I also need to come up with a transmission/gear reduction setup, then set the quick change rear's location. Since this car will have no suspension and a very limited steering range, the axles will both be solidly mounted to the chassis, keeping things very simple. Quote Link to comment Share on other sites More sharing options...
cobraman Posted April 17, 2013 Share Posted April 17, 2013 You must be doing a good job because your driver looks very happy ! : ) Quote Link to comment Share on other sites More sharing options...
Danno Posted April 17, 2013 Share Posted April 17, 2013 We can't see his hands. Quote Link to comment Share on other sites More sharing options...
Chuck Most Posted April 18, 2013 Share Posted April 18, 2013 That looks great, Chuck. Nicely shortened. Will there be a lift off hardtop for it? Not gonna cut off the top only to put on another one. That would be totally counter-productive! Another shortened body will become a cartoonish drag car- Quote Link to comment Share on other sites More sharing options...
Casey Posted April 21, 2013 Author Share Posted April 21, 2013 I wasn't happy with the canopy I had, so I came home from Michael's with a new option, in the form of this Revell 1/48 P-51 kit. This is what I really wanted from the start-- a canopy with a separate, flanged base which I could mount to the body shell. The bare canopy didn't look right sitting directly on the body, so I think this'll be a good solution: Much better, and I can more easily integrate the canopy and its base with the Avanti's hood and cowl bulge (yeah, I'm still holding onto that styling element): I needed to figure out some type of chassis-to-body support, and while passing through the beading aisle at Michael's, I saw some copper pins which looked like they might work well for body support rods. The flat heads will touch the underside of the body in various places, while the opposite ends will be cut to length and soldered to the chassis. I have the body resting on the tops of the tires right now, so once all the body supports are in place, I will add a small round shim between the body and pin heads, which will both positively locate the pin heads and add a tiny bit of needed clearance between the tires and body. Here's a pic of the first pin in place: The belly of the P-51 had what looked almost exactly like a late '80s aero-style snorkel scoop, and it was very close to 1/25 scale, too, so I assembled the plane's fuselage halves and cut away the scoop. I'm not sure this will remain, and I think I have to make the scoop's mouth flush with the rest of the body, but I'm going to work with it for now and see if it sticks: Quote Link to comment Share on other sites More sharing options...
Lunajammer Posted April 22, 2013 Share Posted April 22, 2013 I'm not sure this will remain, and I think I have to make the scoop's mouth flush with the rest of the body, but I'm going to work with it for now and see if it sticks: Flush with the body might make more aero sense Casey, but it would almost defeat the purpose of using the Mustang scoop. I think your instincts are correct the way you have it, at least in terms of the coolness factor. It adds to the allure. Quote Link to comment Share on other sites More sharing options...
Casey Posted April 23, 2013 Author Share Posted April 23, 2013 Flush with the body might make more aero sense Casey, but it would almost defeat the purpose of using the Mustang scoop. I think your instincts are correct the way you have it, at least in terms of the coolness factor. It adds to the allure. It's already been replaced with a different air intake, but now that I've got the chassis-to-body fit locked in, the scoop lies below the bellypan and allows more air under the car. Not good. I think I'll just stick with the smooth nose and add the air intake for the engine on the top of the body as I had originally planned. Quote Link to comment Share on other sites More sharing options...
Casey Posted April 25, 2013 Author Share Posted April 25, 2013 Third time's the charm I guess, as the body ended up with the smooth nose/chin I originally wanted to use: Bellypan still fits: I did some preliminary work on the canopy base, but this piece is very close to what I envisioned from the start, so I shouldn't have any issues working it into the body shell: There's still a long way to go, but I'm pleased with the progress I've made so far: Quote Link to comment Share on other sites More sharing options...
cobraman Posted April 26, 2013 Share Posted April 26, 2013 Looking sharp ! Quote Link to comment Share on other sites More sharing options...
Chuck Most Posted April 29, 2013 Share Posted April 29, 2013 (edited) Well, well, well... lookie here. Stude #2 done blown a bubble... Edited April 29, 2013 by Michigan Madman Quote Link to comment Share on other sites More sharing options...
cobraman Posted April 29, 2013 Share Posted April 29, 2013 What the ??????? Interesting. : ) Quote Link to comment Share on other sites More sharing options...
Chuck Most Posted April 30, 2013 Share Posted April 30, 2013 VW Dave suggested the name "Bubble Butt". Think I'm going to go with it. Quote Link to comment Share on other sites More sharing options...
Chuck Most Posted May 6, 2013 Share Posted May 6, 2013 Now available in red... Quote Link to comment Share on other sites More sharing options...
Casey Posted May 11, 2013 Author Share Posted May 11, 2013 Will Bubble Butt be retaining the yellow(?) bubble or is it going to be a different color? Or no color? Quote Link to comment Share on other sites More sharing options...
Casey Posted August 25, 2013 Author Share Posted August 25, 2013 The canopy just wasn't working out, so I eliminated it and molded the canopy base to the body. I need to attend to two small areas around the canopy base (fairing?), but the underside of the body is finish primed, and one more coat of primer should finish off the exterior for now. Quote Link to comment Share on other sites More sharing options...
Crazy Ed Posted August 25, 2013 Share Posted August 25, 2013 It's Alive! Casey, Good to see the Turbine is back. As too the Drivers "Window", if you have the windscreen from an Indy or F-1 carit might work in well. Quote Link to comment Share on other sites More sharing options...
Chuck Most Posted September 9, 2013 Share Posted September 9, 2013 Will Bubble Butt be retaining the yellow(?) bubble or is it going to be a different color? Or no color? I'll be yellow as a morning tinkle. (Why do I belt out such disturbing little axioms with such frequently?) But, as with the roadster, Bubble Butt has stalled. Really need to get it together.... Quote Link to comment Share on other sites More sharing options...
Casey Posted August 3, 2016 Author Share Posted August 3, 2016 I'll be yellow as a morning tinkle. (Why do I belt out such disturbing little axioms with such frequently?) But, as with the roadster, Bubble Butt has stalled. Really need to get it together.... Yes, yes you (well, I, us, we all...you get the picture) we need to get this going again. Three years really flies by in the blink of an eye. Quote Link to comment Share on other sites More sharing options...
Chuck Most Posted August 4, 2016 Share Posted August 4, 2016 Yikes!No kidding... Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.