kpnuts Posted August 18, 2014 Share Posted August 18, 2014 Hi all here is my next project. I won it off ebay, never don a diecast kit before How do I go about cleaning the corrosion and flash off it and do I need to prepare the metal in anyway before I spray it. Quote Link to comment Share on other sites More sharing options...
1930fordpickup Posted August 18, 2014 Share Posted August 18, 2014 Just use a good metal file on the flash. I do not know about the paint prep. Quote Link to comment Share on other sites More sharing options...
sjordan2 Posted August 18, 2014 Share Posted August 18, 2014 (edited) You should post this again in the diecast models forum at http://www.modelcarsmag.com/forums/index.php?showforum=51 Send a PM to one of the following people, who know this stuff well Art Anderson Scale-Master Or ask your question on Google. This isn't the only model car site out there. Edited August 18, 2014 by sjordan2 Quote Link to comment Share on other sites More sharing options...
kpnuts Posted August 20, 2014 Author Share Posted August 20, 2014 Thank s and thank to whoever moved this post sorry I put it in the wrong place I am new here. Quote Link to comment Share on other sites More sharing options...
Harry P. Posted August 20, 2014 Share Posted August 20, 2014 Thank s and thank to whoever moved this post sorry I put it in the wrong place I am new here. I moved it. No problem. Quote Link to comment Share on other sites More sharing options...
Harry P. Posted August 20, 2014 Share Posted August 20, 2014 To answer your question, you remove the flash by simply bending it back and forth until it breaks off, then clean up with files and/or sandpaper. You can clean the surface with steel wool, which will get into all the crevices better than sandpaper would. Quote Link to comment Share on other sites More sharing options...
kpnuts Posted August 21, 2014 Author Share Posted August 21, 2014 Hi all well I've started cleaning the bodywork, getting rid of the flash and checking the fit, I think I have a lot of work where that is concerned its a terrible fit anyway I sprayed the engine black as per the instructions. then I thought I would do some research as I want to do a good job of it and discovered the engine has no black in it, it's silver and green so thats where I am now, looking to find what I can use for the ht leads from the spark plugs. Quote Link to comment Share on other sites More sharing options...
Harry P. Posted August 21, 2014 Share Posted August 21, 2014 You can gently and slightly bend the fender unit to get a better fit with the body. But be careful... diecast metal is very brittle and will crack if bent too far. As far as correct engine color, or getting the details correct, period... you need to do a google image search. There are hundreds of photos online that you can reference. http://www.google.com/search?q=1931+packard+dual+cowl+phaeton&safe=off&source=lnms&tbm=isch&sa=X&ei=qkH2U_KBH4ynyATw4oCoBg&ved=0CAYQ_AUoAQ&biw=1529&bih=893 http://www.google.com/search?q=1931+packard+engine&safe=off&sa=X&tbm=isch&tbo=u&source=univ&ei=HUL2U_rQKIb2yQS2soGoBg&ved=0CB4QsAQ&biw=1529&bih=893 Quote Link to comment Share on other sites More sharing options...
kpnuts Posted August 21, 2014 Author Share Posted August 21, 2014 Thanks for that, yes I tried filling it to fit and nothing appears to be fouling but it still has that gap so probably should bend it, would it help to heat it up in order to stop it cracking. Quote Link to comment Share on other sites More sharing options...
kpnuts Posted August 22, 2014 Author Share Posted August 22, 2014 Well I've done some weathering on the engine, I am aiming to make this as realistic as i can (so dont expect too much) I thought I would start the weathering the engine before I put all the other bits on as it wont be so easy to get at once they are on. Quote Link to comment Share on other sites More sharing options...
Harry P. Posted August 22, 2014 Share Posted August 22, 2014 Thanks for that, yes I tried filling it to fit and nothing appears to be fouling but it still has that gap so probably should bend it, would it help to heat it up in order to stop it cracking. The man to ask about working with diecasts is Cliff Read. He is an absolute master. His forum screen name is traditional... I'd send him a PM if I were you... I guarantee he can answer your questions. Quote Link to comment Share on other sites More sharing options...
sjordan2 Posted August 22, 2014 Share Posted August 22, 2014 Is that engine color metallic? If so, it's waaayyy off. But I don't know what you have in mind. Quote Link to comment Share on other sites More sharing options...
kpnuts Posted August 24, 2014 Author Share Posted August 24, 2014 it's not supposed to be but it does look it in the photos, not in the flesh though, tbh I prefer it in the photos anyway here is tonight's episode. I've made a start on the base too it's going to be a garage . Quote Link to comment Share on other sites More sharing options...
kpnuts Posted August 25, 2014 Author Share Posted August 25, 2014 Hi all here is tonights episode. I drilled out the distributor so I could put the HT leads in. then I made the HT leads out of thin solder wire. Then I cut them to length and squished the ends to make the tabs to connect them to the spark plugs. Then I noticed from the ref photos I have that there are rivets and badges on the starter motor and solinoid so I added them. still loads of detail to add to the engine bay, got an idea for making the jubilie clips for the radiator hoses and I am going to attempt to make the fuel pump and assossiated pipes as they are only vaugley moulded into the firewall. Quote Link to comment Share on other sites More sharing options...
Harry P. Posted August 25, 2014 Share Posted August 25, 2014 Nice work so far. I'll be watching... Quote Link to comment Share on other sites More sharing options...
hooknladderno1 Posted August 26, 2014 Share Posted August 26, 2014 (edited) Ken, Seeing your thread for the first time. While no expert, I can offer a few suggestions. As far as removing the oxidation on the larger portions of the body, larger hobby sanding sticks or nail files can help. Switch to finer grades as the oxidation is removed. Once clean, wash with a degreaser and rinse well. Dry immediately to prevent further oxidation. I don't know if you have "self etching primers" available in the UK. Application of one as soon as possible after the above step would be ideal. This primer actually binds itself to the metal for excellent paint adhesion. Depending upon your desired color(s) use either Tamiya Fine Surface Primer or automotive primer. As for filling gaps, you can use epoxy putty or my new favorite - "Perfect Plastic Putty". If the gap is large, back the area with some thin styrene super glued in place. If you have any other questions, PM me. HTH. David Edited August 26, 2014 by hooknladderno1 Quote Link to comment Share on other sites More sharing options...
kpnuts Posted August 27, 2014 Author Share Posted August 27, 2014 Thanks for the advice. Lots of ideas for this kit so many in fact I am having trouble deciding. Quote Link to comment Share on other sites More sharing options...
kpnuts Posted August 27, 2014 Author Share Posted August 27, 2014 Hi all here is tonight's installment, done nothing to the car but got a fair amount done on the garage lift. Quote Link to comment Share on other sites More sharing options...
kpnuts Posted August 30, 2014 Author Share Posted August 30, 2014 Hi all Well I've got the under coat and the first top coat on the Packard now. Quote Link to comment Share on other sites More sharing options...
kpnuts Posted August 31, 2014 Author Share Posted August 31, 2014 Here is todays progress on the Packard Quote Link to comment Share on other sites More sharing options...
kpnuts Posted September 1, 2014 Author Share Posted September 1, 2014 Here is todays bit on the packard. the fuel pump and filter are not included with the kit so I decided to have a go at making them. and I had a go at making the seats look like old cracked leather(quite unsuccessfully) any suggestions ? Quote Link to comment Share on other sites More sharing options...
DynoMight Posted September 1, 2014 Share Posted September 1, 2014 The color combo is great! On the wheels, is there a backing plate behind the wires? If there is, paint that black. It will give the wires depth. Quote Link to comment Share on other sites More sharing options...
kpnuts Posted September 3, 2014 Author Share Posted September 3, 2014 Hi glen no there is not but maybe I could make one and see how it looks. Anyway all here is todays hard graft. Quote Link to comment Share on other sites More sharing options...
Harry P. Posted September 3, 2014 Share Posted September 3, 2014 The dash looks great. You really nailed it with the silver detail painting. Nice job. Quote Link to comment Share on other sites More sharing options...
kpnuts Posted September 4, 2014 Author Share Posted September 4, 2014 Thanks Harry, took 3 attempts and about 4 hours but I was pleased with the results ( I actually had someone ask me if it was wood) that made the effort well worth it. Anyway here is tonight's progress on the Packard Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.